Q0: Why was the GB4000's RF Carrier changed from 2.4 MHz to 3.1 MHz?
A: The importance of sideband frequencies in historical frequency machines has been discovered in the last decade and 3.1 MHz has been mathematically proven to be the 'Ideal' carrier frequency for many purposes and for doing very powerful sweeps.
Q1: Does the GB-4000 output its frequencies digital or analog?
A: Analog.
Q2: Does the GB-4000 use crystal controlled frequencies for high accuracy.
A: Yes it does for the RF carrier frequency. The GB-4000 also goes beyond using crystal-controlled frequencies. It also uses digital frequencies output from a DSP (Digital Signal Processor).
Q3: How does the GB-4000 frequency Instrument output its frequencies analog when they come from a digital DSP chip?
A: The GB-4000 uses a DAC (Digital to Analog Converter).
This type of electronic circuit is used in all modern analog frequency generators. The frequencies are output from a DSP, (Digital Signal Processor) then go through the DAC and then through a low pass or band pass filter and come out converted to analog. These frequencies are phase-locked-looped for perfect accuracy. By this method we have all the harmonic content of the old antique vacuum tube frequency generators along with the digital accuracy. No old antique frequency generator has the frequency accuracy of today’s modern equipment. This method is now the standard in the industry. We recommend that you read this page “The Analog Vs Digital Frequency Debate.”
Q4: Can the GB-4000 frequency machine output RF or Radio Frequencies.
A: Yes. The GB-4000 has a frequency range from .01 to 20 million hertz (20 Megahertz).
Q5: What is an RF Carrier Frequency?
A: Any radio station uses a carrier frequency to carry or modulate (piggyback) the audio frequencies, voice or music that is sent out for you to hear on your radio. Modulation is the mixing of the RF carrier frequency with the audio frequencies. So, the RF carrier frequency is the means by which the radio station transmits the signal through the air to you the listener.
Q6: Why do other frequency generator manufacturers limit their audio frequency modulation to 1000 hertz?
A: Most likely they just did not want to spend the money to build the circuit with a higher capability. This is just one of the several differences between the GB-4000 and all the other frequency generators on the market today. The GB4000 can modulate any frequency from .1 hertz to 999,999 hertz on its carrier frequency.
Q7: What is the main difference between the GB-4000 and other function generators?
A: The GB-4000 can output up to 8 audio frequencies simultaneously up to 40,000 hertz.
Q8: What is the highest frequency that the GB-4000 can output?
A: 20 million hertz.
Q9: Most other manufacturers only have a frequency range to 10,000 hertz. Some go up to 21,275 hertz. The GB-4000 goes to 20,000,000 hertz. Why?
A. It is all a matter of what frequency range the manufacturer wants to cover. The higher the frequency range the more versatile the generator will be.
Q10: How much more powerful is the GB-4000 than other frequency generators?
A: Because of the use of an RF carrier frequency the GB-4000 is over 18 times more powerful than most other frequency generators. If the SR-4 amplifier is connected to the GB-4000 it is over 75 times more powerful than other frequency generator that do not use a carrier frequency.
Q11: Why do I need the optional Amplifier?
A: The GB-4000 can operate in two different modes. 1: RF Mode, which is the higher frequency mode 2: Audio Mode, which is the lower frequency mode. In RF mode, the GB-4000 has an output of about 3.7 watts; however, sometimes more power is wanted. The SR-4 Amplifier boosts the 3.7 watt RF output to about 15 watts of RF output. Also, the Amplifier has three additional sets of outputs for more hookups. The SR-4 15-Watt Amplifier operates in the RF mode only.
Q12: Why was the GB-4000 built to output up to 8 frequencies simultaneously while other instruments only output one frequency at a time?
A: It was designed to be a time saving feature.
Q13: Does the GB-4000 show the actual frequency being used on the LCD?
A: Yes. The GB-4000 shows the actual frequency on the LCD as long as you are not running multiple frequencies.
Q14: Some manufacturers build their instruments with built in rechargeable batteries. Why doesn't the GB-4000 have this capability?
A: The reason the GB-4000 is not battery operated is because of its power output range. Rechargeable instruments only have 28 volts peak to peak voltage output. In the audio mode the GB-4000 is variable and has a range from 0 to 36 volts peak to peak. In the RF mode the GB-4000 is variable from 0 to over 110 volts peak to peak. Because of these capabilities it is not feasible to put batteries into the GB-4000.
Q15. Does the GB-4000 have programmable memory?
A: Yes. It has enough memory to program up to two thousand auto channels holding 48 frequencies each.
Q16: What is gating and how does it work?
A: Gating is basically an advanced "pulsing" feature. When turned on it pulses any frequency on and off at the pre-determined gate rate.
Q17: Why does the GB-4000 have a 10% to 90% duty cycle range?
A: All high quality frequency generators have this capability because different duty cycles are needed in testing.
Q18: Can the GB-4000 sweep between frequencies like all high quality frequency generators?
A: Yes. One of the great features of the GB-4000 is that it is capable of doing two kinds of sweep functions. 1) SWEEP: Allows you to run a specified frequency range of your choosing, one frequency at a time. The instrument sweeps from your beginning frequency to your ending frequency. 2) CONVERGENCE SWEEP: Allows you to run two frequencies at a time over a specified frequency range of your choosing. The instrument sweeps from your beginning frequency to the ending frequency and at the same time sweeps from the ending frequency to the beginning frequency. The result is that the two frequencies sweep towards each other, then pass each other, one going up and the other going down and each ending where the other frequency began.
Q19: Why does the GB-4000 have a channel sweep capability which varies the frequency slightly?
A: The GB-4000 has the capability to sweep when running any of the 2000 programmable auto channels. The channel sweep only covers a 20,000 hertz sweep. If you run the instrument for only three minutes then it would be on each frequency for 16 seconds. This type of sweep is desirable when you want variability in your frequency or frequencies you are running.
Q20: Why do you use a membrane type keypad instead of the contact style?
A: Durability is the main reason. Membrane keypad switches are the industry standard and have been for many years. Almost all electronic devices that have keypads use them. They are built to last for many years. They replaced the contact style because they have fewer problems. They will generally outlast the electronics. We have had this type of keypad on our instrument for over 8 years under heavy use with very few problems.
Q21: How long will the GB-4000 last?
A: The GB-4000 is built to last a long time and 99.9 % of the instruments sold over the last several years are still working, many are well over 10 years old now and some pushing 15 years and still going strong. Some manufacturers claim that their instrument will last a lifetime. We cannot and will not make that kind of misleading claim. We would be foolish to make such a claim. Any instrument that cannot be repaired, even after years of use, is replaced with the current model for only $750. No other company that I know of offers this kind of replacement in the industry.
Q22: Is the GB-4000 easy to use?
A: Yes. Programming the GB-4000 is easy. Running an un-programmed frequency is also easy to do. To run a programmed channel all that the user has to do is press the Auto channel button, then enter the auto channel number using the keypad, then press the Run button. The GB-4000 then will run all the frequencies in the channel. To run an individual frequency all you have to do is press enter then put in the frequency you wish to use and then press run. Anyone can do this three step process.
Q23: Why does the GB-4000 cost less than almost all the other instruments when it has far more features?
A: We purchase direct from the manufacturer. There are no middlemen to make it more expensive.